Hunter 59135 Instalační příručka Strana 1

www.HunterFan.com1.888.830.1326PAGE7PAGE13PAGE10PAGE5PAGE630 inches7 feetPAGE2What to Expect with Your InstallationCeiling BracketLadderPAGE3Tools Nee

www.HunterFan.com1.888.830.1326WiringFROM FANFROM CEILING BRACKETFROM FANUsing an orange wire connector from the hardware bag, connect the 3 gr

www.HunterFan.com1.888.830.1326CanopyLift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into pla

www.HunterFan.com1.888.830.1326BladesLightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten

www.HunterFan.com1.888.830.1326Remove and discard the plastic connectors from the ends of the two pull chains. Remove the pre-installed light kit asse

www.HunterFan.com1.888.830.1326Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the two screws a

www.HunterFan.com1.888.830.132615M3556-01 • 06/17/14 • © Hunter Fan CompanySwitch Housing & Light Kit (continued)Make sure the lower switch housin

www.HunterFan.com1.888.830.1326Switch Housing & Light Kit (continued)Install the fourth light kit assembly screw and tighten all four screws secur

www.HunterFan.com1.888.830.132617M3556-01 • 06/17/14 • © Hunter Fan CompanyGlobeFeed the pull chains from the fan switch and the light switch down thr

www.HunterFan.com1.888.830.1326Globe (continued)Align the keyhole slots in the globe assembly with the partially installed screws in the light kit ass

www.HunterFan.com1.888.830.1326Maintenance & CleaningONTurn PowerChanging the bulbs - carefully remove the globe assembly. Unscrew the bulbs and r

www.HunterFan.com1.888.830.1326M3556-01 • 06/17/14 • © Hunter Fan Company1.888.830.13261.888.830.1326What to Expect with Your InstallationKnow your wi

www.HunterFan.com1.888.830.1326Troubleshooting Excessive wobbling• Tighten all of the blade and blade iron screws until they are snug.• Turn the

www.HunterFan.com1.888.830.1326Tools NeededLadderPower Drill (optional)9/64” Drill Bit (optional)ScrewdriversPliers Wire StrippersIf mounting to a sup

www.HunterFan.com1.888.830.13264M3556-01 • 06/17/14 • © Hunter Fan Company1.866.268.1936If you have an angled ceiling:1. You will need a longer downro

www.HunterFan.com1.888.830.1326Ceiling BracketRefer to warning w.1 on pg. 2To avoid possible electrical shock, before installing your fan, disconnect

www.HunterFan.com1.888.830.1326Motor HousingGently lower the motor housing so it rests in place on the motor assembly.Align the screw holes in the top

www.HunterFan.com1.888.830.13267M3556-01 • 06/17/14 • © Hunter Fan CompanyDownrodSlideSlide1 2 3 4 5678910Sold SeparatelyIncludedLonger Downrodfor ang

www.HunterFan.com1.888.830.13268M3556-01 • 06/17/14 • © Hunter Fan CompanyKEEP!8”3/8”CUT& STRIP(not to scale)Remove the pre-installed setscrew so

www.HunterFan.com1.888.830.1326Downrod (continued)DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling b